A Think Again Media Group publication
Gun Debunk

Shotgun gauge and bore size

Shotgun gauge: bore size, shot size and historical measurements

By Phil Springer, Editor · Published · Gun Debunk

Shotgun gauge: bore size, shot size and historical measurements

Shotgun gauge describes the diameter of the bore through an old measure based on a pound of lead. In that system, twelve lead balls of the same diameter as a 12-gauge bore together weigh one pound. Twenty balls matching a 20-gauge bore weigh the same amount. The higher gauge number therefore corresponds to a smaller bore. The number identifies the barrel's size category; it does not count the pellets inside a modern shotgun cartridge.

The common bore-size sequence runs from 10 gauge through 12, 16, 20 and 28, but historical and less common ammunition labels include 14, 24 and 32 gauge. Pellet sizes use another descending numerical sequence. In American shot terminology, sizes increase as the numbers run from 12 toward 1, followed by lettered sizes including B, BB and BBB. Buckshot has its own sequence, progressing from 4 through 3, 2, 1, 0, 00 and 000. English and continental European shot-size conventions differ from the American system.

The .410 bore follows a different convention. Its number states the internal diameter in inches: 410 thousandths of an inch. It is a caliber designation rather than a shotgun gauge number based on lead-ball weight. Expressed under the traditional gauge calculation, it would be approximately 67½ gauge. The decimal point therefore signals a change in the kind of measurement being stated. A .410 and a 20 gauge cannot be ranked by reading their labels as numbers on one common scale.

Bore diameter is also separate from the size of the shot. Modern shotgun cartridges normally carry multiple pellets, and those pellets have their own size designations. Shotgun gauge belongs to the firearm and cartridge size category; a shot number identifies a different property of the contents. Neither designation states the total weight of the pellet charge. Several measurements can appear together because they describe different parts of the same cartridge rather than competing definitions of its size.

The total shot charge is commonly expressed by weight in ounces in American labeling and grams in European labeling. A charge of about 28 grams is approximately one ounce. Buckshot can instead be described by the number of pellets. Shot material is another independent characteristic, with lead, iron-based steel shot and tungsten formulations among the possibilities. Gauge, pellet diameter, payload weight and material remain separate descriptions even when all appear on the same package.

Cartridge length introduces another dimension. The stated length relates to the chamber and the opened case rather than simply the shorter folded cartridge as it appears before firing. American descriptions commonly use inches, while European descriptions use millimeters. This length convention does not alter the lead-ball definition of shotgun gauge. Two cartridges can belong to one gauge category while carrying different length designations, because bore width and chamber length measure different dimensions.

An older marking, dram equivalent, preserves another part of shotgun history. It compares the performance of a smokeless-powder cartridge with the amount of black powder that would produce the same velocity with the same shot charge. A dram was a unit of weight. The marking therefore refers to a historical comparison, rather than to the gauge or pellet count. Modern velocity figures describe a speed, while dram equivalent encodes that speed through an older propellant-based convention.

The shotgun's specialized role developed from earlier smoothbore firearms. Before rifled barrels became widespread, a gun could carry either one projectile or several. Sporting arms developed around the use of multiple projectiles over relatively short distances. Changes in ignition systems helped make them practical for hunting birds and other game. The evolution from early matchlocks through spark-producing locks preceded modern cartridge forms, leaving a vocabulary whose origins reach well before present-day ammunition packaging.

A surviving French fowling gun made for Louis XIII around 1620 captures that earlier sporting world. Produced in the Le Bourgeois workshop at Lisieux, it is among the earliest examples of French flintlock construction. Its walnut stock has an unusually graceful scroll-shaped end. Steel, brass, silver, gold and mother-of-pearl appear among its materials, while the king's crowned monogram identifies its patron. Louis was an enthusiastic hunter, collector and amateur gunsmith, associated with the nickname Louis the Gun-Maker.

The royal fowling piece carries silver and brass wire, engraved silver and mother-of-pearl ornament. It came from the workshop directed by Marin Le Bourgeois, brother of Pierre. Marin is traditionally credited with the French flintlock’s invention. The scroll-shaped butt is an especially unusual feature. The museum acquired the gun through the Rogers Fund and Harris Brisbane Dick Fund in 1972. Its materials belong to the court crafts of the early 17th century, while its surviving lock places that decoration on an early example of a developing ignition system.

The Question

How does bore size change as a shotgun gauge number rises?

Show the answer

The Answer

The bore gets smaller: a 12-gauge bore is larger than a 20-gauge bore. The traditional gauge measure counts how many bore-sized lead balls together weigh one pound.

Send this question to a friend

Read next

By clicking “Send me the real story” you agree to Gun Debunk’s Terms of Use and Privacy Policy.